Interior design for crazy...

Internal Zama frame for Ale 840 tractor

IR receiver with cable with plug for Intellibox

This receiver allows the simultaneous use of 7 IRIS remote controls

Jazz A42/A43/A45 Intermediate Car Frame

Led stand with cabin decor for class 37 BR

Faithful to the original working lifting magnet BvM L34-170 from the company J.

Braun GmbH

Usable with crane models from all manufacturers.

With connecting plug for our gantry crane 80 000. 

Lighting board for Mazinger

Lighting board/third headlight/tail lights for dummy

LISSY infrared transmitter

LISSY consists of an infrared transmitter mounted on the vehicle and a receiver module, whose infrared sensors

are integrated into the track. The locomotive address, train category, speed and direction of travel detected by the

infrared transmitter are recognized by the receiver and transmitted to the LocoNet. In addition, a wide variety of

automatic control functions can be implemented without the use of a computer.

LISSY Receiver 

LISSY receiver 68 610 uses a single sensor only. For this reason only those LISSY functions

using a single sensor can be implemented. These are the switching operation, reading of the

locomotive data and the transfer of this data to the LocoNet. All automatic functions like

shuttle operation, holding point, block-section or station control are not possible with this

receiver.

FS E.326 004 electric locomotive in Isabella Brown livery, without mechanical compressor, with D'Arbela separator. Bologna Central Station Dep.

Provision for 8-pole decoder.

Inner frame with metal motor housing and gear housing. Transmission with worm gear and flywheels on two central axles.

The entire outer frame, including the stop beams, is painted metal. Metal handrails. Precision-cast brass wheels with steel rims

and one axle with traction tyres.

LocoNet IR Receiver 63830

IRIS receiver for connection to LocoNet central stations

1. Description

With the LocoNet IR set, locomotives, points and tracks can be controlled wirelessly from any digital LocoNet central station. Simply connect the LocoNet IR receiver to the LocoNet to control everything on the layout with up to four different IRIS handheld transmitters. With this receiver, you can also use the IRIS IR remote control or PIKO Digi-Fern with B-Basic, IB-Com, DAISY and ProfiBoss.

LocoNet Occupancy Detection Modules for 2-Rail Operation

The module provides sixteen inputs, each of which

is used to monitor a section of track.

One rail in each sector must be isolated from

the rest of the track and connected to the detector input.

A vehicle will trigger a Occupancy message

by bridging the sector rails with its non-isolated wheelsets.

All inputs can also be shorted to ground via a reed contact or a manual switch to

also generate the message.

Module for 3-Rail operation

The module provides sixteen inputs each

of which is used to monitor one track section.

One rail of each sector must be insulated

from the rest of the layout and connected to

the detector input. A vehicle will trigger an

occupancy message by bridging the sector's

rails with its non-insulated wheelsets. All

inputs may also be shortened to ground by

a reed-contact ora manual switch to likewise

generate the message.

A change of state caused by a vehicle entering

or leaving that section wilf be refayed

by a LocoNet message to the master or

other LocoNet devices, e.g. IB-Switch.

Power supply: Why is a power supply needed?

The Intellibox and TwinCenter provide 0.5 A (LocoNet T output) or 0.2 A (LocoNet B output) of power for

the devices connected to their LocoNet outputs. If many devices (IB-Control, IB-Switch, etc.) are used

on the LocoNet, the maximum load on these connections may be exceeded. To calculate the current load

on the LocoNet, the following values ​​must be used:

IB-Control 65400 0.12 A

IB-Switch 65800 0.14 A

FRED 66000 0.02 A

Feedback sensor 63340 0.01 A

Feedback sensor 63350 0.01 A

For example, if three IB-Control and one IBSwitch are connected to the Intellibox, the maximum current load

of the LocoNet T output of 0.5 A is reached. If you want to connect additional devices, they must be powered

via the 63100 power supply